Sellier & Bellot bullets

[MS 9x56]

That's correct, 8mm is as large as we go on that bullet type.

I am going to see if my LGS can order me in several boxes of the 9.3x62 as I love hunting with my CZ 550 FS. Can you tell me what the FPS are in that load?

 

[Tango]

Velocity on that load is 2,280 FPS from a 23.5" barrel. We don't have anything in stock, but more of it should be in July production.

 

[Tango]

Any chance S&B will make the 7mm SPCE bullet available for reloaders?

No plans to do so at this time. Demand for loaded ammunition still exceeds capacity, so everything goes into internal production. We'll have all copper XRG SPCE loads out this Fall. I'll be shooting it for the first time next week. Looks promising especially for the European markets where lead will be banned in the not too distant future.

Rifle ammunition with eXergy Edge bullets – Sellier & Bellot

www.sellier-bellot.cz

 

[MS 9x56]

Velocity on that load is 2,280 FPS from a 23.5" barrel. We don't have anything in stock, but more of it should be in July production.

So about on par with PPU?

 

[Tango]

So about on par with PPU?

Sorry, I'm not familiar with their load

 

[aandy767]

173gr SPCE

Tango, maybe you can tell me I my M77 has great difficulty loading the 173gr 7x57. leaves witness marks of the riffleing on the bullets. also hard to remove, the bullet did stay in the case so powder did not go every where. loaded and shot some S&B 140 or 139's great.

have you seen this before?

 

[rookhawk]

173gr SPCE

Tango, maybe you can tell me I my M77 has great difficulty loading the 173gr 7x57. leaves witness marks of the riffleing on the bullets. also hard to remove, the bullet did stay in the case so powder did not go every where. loaded and shot some S&B 140 or 139's great.

have you seen this before?

@aandy767 it sounds like you have a short throated 7x57 akin to a 7-08. It probably was made for 140gr bullets. You can have the throat lengthened so that it shoots 175gr bullets.

@Tango I’m not sure if you’re the fellow I purchased several cases of ammo from over the years? I interacted with a Magtech exec that personally liked 7x57 and used his influence to get S&B 175gr Nosler Partition Ammo imported. Do you import that loading any longer or offer any other 7x57 loads that use bullets from the industry at large? (E.g. not bullets made by S&B)

 

[Grumpy gumpy]

Sounds like a throat issue, may need to check the throat depth to see what’s going on there.
I use the 8mm 196 gn spce in my 8x68 and they are silly accurate, same as my friends 308with the 180gn spce factory loads
Gumpy



Just realised rookhawk said the same thing

 

[MS 9x56]

It seems most US manufacturers rifles are not throated as long as European arms. It is a shame.

 

[Tango]

173gr SPCE

Tango, maybe you can tell me I my M77 has great difficulty loading the 173gr 7x57. leaves witness marks of the riffleing on the bullets. also hard to remove, the bullet did stay in the case so powder did not go every where. loaded and shot some S&B 140 or 139's great.

have you seen this before?

Just sent a PM. Thank you

 

[Tango]

@aandy767 it sounds like you have a short throated 7x57 akin to a 7-08. It probably was made for 140gr bullets. You can have the throat lengthened so that it shoots 175gr bullets.

@Tango I’m not sure if you’re the fellow I purchased several cases of ammo from over the years? I interacted with a Magtech exec that personally liked 7x57 and used his influence to get S&B 175gr Nosler Partition Ammo imported. Do you import that loading any longer or offer any other 7x57 loads that use bullets from the industry at large? (E.g. not bullets made by S&B)

Yes sir, that's me. Unfortunately, we have not been able to get the Partitions any longer at a reasonable cost after all the freight to export etc. I'm using my stash sparingly as it's my favorite. Everything we load currently uses an internally produced projectile. We do have a new copper solid HP coming out this year called the XRG Edge. It's 150gr in 7x57. I'm not typically a fan of copper bullet performance in small-med calibers (due to limited expansion and upset) but this SPCE type profile completely changes the way to bullet upsets. I've been using it in Europe for a couple years in 308 and 7x57 and it's devastating. Not a high BC, long range bullet, but out to 300 it's excellent.

Rifle ammunition with eXergy Edge bullets – Sellier & Bellot

www.sellier-bellot.cz

 

[rookhawk]

Yes sir, that's me. Unfortunately, we have not been able to get the Partitions any longer at a reasonable cost after all the freight to export etc. I'm using my stash sparingly as it's my favorite. Everything we load currently uses an internally produced projectile. We do have a new copper solid HP coming out this year called the XRG Edge. It's 150gr in 7x57. I'm not typically a fan of copper bullet performance in small-med calibers (due to limited expansion and upset) but this SPCE type profile completely changes the way to bullet upsets. I've been using it in Europe for a couple years in 308 and 7x57 and it's devastating. Not a high BC, long range bullet, but out to 300 it's excellent.

Rifle ammunition with eXergy Edge bullets – Sellier & Bellot

www.sellier-bellot.cz

Glad to meet you on this forum now that I can put a name to the handle! I think I'm down to about 12 rounds of the 175gr S&B Partitions. I really hate handloading, but I want a heavy-for-caliber round for Africa and North America. What would be your advice to the forum for those with similar preferences?

P.S. - I know its asking a lot and it would cost a lot, but the world would be your oyster if you'd offer Swift A-frame loads for 7x57. The world has gone mental for 140gr bullets and many of us want that 175gr with a tough jacket so the 7x57 can box above its weight class.

 

[Josh P]

The world has gone mental for 140gr bullets and many of us want that 175gr with a tough jacket so the 7x57 can box above its weight class.

Listen to this man.

 

[Uncontrolled_round_feed]

Glad to meet you on this forum now that I can put a name to the handle! I think I'm down to about 12 rounds of the 175gr S&B Partitions. I really hate handloading, but I want a heavy-for-caliber round for Africa and North America. What would be your advice to the forum for those with similar preferences?

P.S. - I know its asking a lot and it would cost a lot, but the world would be your oyster if you'd offer Swift A-frame loads for 7x57. The world has gone mental for 140gr bullets and many of us want that 175gr with a tough jacket so the 7x57 can box above its weight class.

Agreed. I think buyers would pay a premium for this option fwiw

 

[rookhawk]

It seems most US manufacturers rifles are not throated as long as European arms. It is a shame.

This is why I have an irrational hatred for the 7mm08. It "should" be just as good as a 7x57 but almost all of them are tuned for 140gr and short throats. This infection in design has effected many of the newer 7x57 / 275 Rigby rifles, neutering their storied "super powers" and turning them into "meh" guns.

I think Franz Davis just sent his Highland Stalker out to have the throat lengthened to overcome this modern design flaw putting the weapon back into the original design that earned all its accolades.

TLDR; don't get a short throated 7mm.