Hornady CX Bullets

I use the GMX 130gr Outfitter in my 270 win and has performed really great from me. On red stags primarly and this year on a mid asian ibex at 300m and a roe deer at 240 and 290 m.

I have about 200 rounds left before i try the CX Outfitter. Have only recovered 3 and all mushromed perfecfly.
 
Last edited:
I'd like to get input on Hornady 250 grain CX loads for my Win 70 .375 H&H. Factory Hornady ammo shows 2,700 fps muzzle. For powder, I have a pound each to try of Accurate 4064, Hodgdon H4350, and IMR 7828 (which I use for 180 grain Nosler Partitions in my 200 WBY). CX would be for PG, and factory 300 gr DGX /DGS for DG.
 
I've seen CSX bullets recovered from hunts I've conducted here at home and recently in AK. I was not impressed with the performance of the bullet. It seems that it just mushrooms a little bit versus a TSX that the petals open up nicely.
They claim that they cause less fouling than other monometal bullets. That's about all I know.
 
I'd like to get input on Hornady 250 grain CX loads for my Win 70 .375 H&H. Factory Hornady ammo shows 2,700 fps muzzle. For powder, I have a pound each to try of Accurate 4064, Hodgdon H4350, and IMR 7828 (which I use for 180 grain Nosler Partitions in my 200 WBY). CX would be for PG, and factory 300 gr DGX /DGS for DG.

Not exactly answering your question, but still relevant info: I shot some factory Hornady Outfitter 250 gr GMX in my 375 Ruger with a 23 inch barrel. Shooting over my MagnetoSpeed, I was getting 2800 FPS and very consistent velocity. Extremely good for factory ammo.

The GMX is sort of the predecessor to the CX bullet and they are both sort of like Barnes bullets.

The biggest issue I had with the 250 GMX was they had a POI several inches higher at 100 yards, compared to my 300 gr Swift A Frame load at 2500 FPS. For this reason, I decided not to shoot two different weight bullets. Just shoot everything with a 300 gr Swift A Frame.

1734613396352.png
 
I'd like to get input on Hornady 250 grain CX loads for my Win 70 .375 H&H. Factory Hornady ammo shows 2,700 fps muzzle. For powder, I have a pound each to try of Accurate 4064, Hodgdon H4350, and IMR 7828 (which I use for 180 grain Nosler Partitions in my 200 WBY). CX would be for PG, and factory 300 gr DGX /DGS for DG.
I use 250 cx in my 375 ruger, 2800 fps , it’s really splitting hairs on performance between TSX & CX imo , H4350 is my go to on reloading stuff , I load 80.00 gr h4350 on everything, in my ruger , and my buddy 78gr in his 375 h&h ( check load data and ladder up or down)
 
Last edited:
I use 250 cx in my 375 ruger, 2800 fps , it’s really splitting hairs on performance between TSX & CX imo , H4350 is my go to on reloading stuff , I load 80.00 gr h4350 on everything, in my ruger , and my buddy 78gr in his 375 h&h ( check load data and ladder up or down)
I would expect the terminal performance difference would be small. Between those two, I would go with what shot best in my rifle. I happen to have started with Barnes so have stuck with it for the conventional expanding monolithic type bullets.
 
Was on the range today testing the 180gr CX in the 300H&H.
I was getting a horrible flyer on every third shot yesterday, but a little extra powder pulled three shots together to .40” today.
Also been playing with the TSX lately.

The TSX was easier to find an accurate load for.
The CX seems to prefer a slightly fouled barrel vs the TSX.
TSX is about 50fps faster.
Both like a lot of jump.
Both run quite a bit slower than lead core bullets at similar pressures.

In a 375, I’d load whichever is most accurate and go hunt a buff with confidence.
 
Clean bore shot is way off the others.
IMG_0454.jpeg
 
I did a plains game hunt last August with a CA Mesa also in 300 PRC, and I used the Hornady outfitter 190gr load for the duration of the hunt. I took big bulls of Eland, Kudu, Waterbuck, Gemsbok, and Impala. I had a total pass through double lung on the eland, and the large Kudu Bull was frontal chest shot which put him down in his tracks. In fact, everything I shot with the rifle and load, absolutely shuttered and were hit extremely hard. I had fantastic performance with this load, and would highly recommend.
7B736D49-C66A-41DF-9270-A69B8DC603DD.jpeg
E3A6ED17-7EFD-4A06-A1F6-5F0C1D3DDEAC.jpeg
24E9A843-583E-4AF8-A0A3-62A7D9EEE81B.jpeg
 

Forum statistics

Threads
65,459
Messages
1,444,909
Members
136,130
Latest member
ArnulfoJ52
 

 

 

Latest profile posts

Made it to Augusta Georgia yesterday for a meeting, hunt bookings are looking good for 2026 and 2027, had a great time on our Alabama safari shot a rutting deer at 200 yards with 7mm PRC near Huntsville and then headed on to Butler Alabama and semi guided my first deer ever shot a very nice broken off 8 point with hunter there and spend a few days on 1100 acres hunting preserve awesome place!
Ray B wrote on JMJ888's profile.
I am righthanded, so not interested in the rifle, but I have a 375 RUM and 350 gr bullet loading data is very hard to come by. If you could reply with information regarding your loads I would greatly appreciate it. Thank you, Ray Boone, Leavenworth, WA
mcr wrote on gbflyer's profile.
Hello - I was looking at your post from several years ago regarding the Winchester 300 H&H. Any chance you still have the lefty M70 300 H&H for sale?
Thank you, Mike
'68boy wrote on Rare Breed's profile.
Wife and I will attend ah dinner in Nashville Friday night. Jay Sheets and wife Chris
crossfire3006 wrote on Hornedfrogbbq's profile.
An excellent AH member right here! I had a fantastic transaction with Hornedfrogbbq (I was the seller). His communication was first rate, payment was extremely fast, and I would have absolutely no reservations at all dealing with him again. Thank you, F!
 
Top