308 bullet

Here is a pic areaonereal was referring to... 168gr Barnes tsx that took a gemsbok at 200yds broadside and was found in off shoulder. You can see entry below. Shot placement could of been better, but I did get a photo opportunity. Lol
image.jpg

image.jpg
 
  • Like
Reactions: lcq
GREAT DEFORMATION!.... Whath a bullet... In my country, all the hunters says wonders about this brand!
 
Last edited by a moderator:
Here is a pic areaonereal was referring to... 168gr Barnes tsx that took a gemsbok at 200yds broadside and was found in off shoulder. You can see entry below. Shot placement could of been better, but I did get a photo opportunity. Lol
View attachment 32403
View attachment 32404

nice gems. picture perfect mushroom. what cal were you shooting?
 
Let me bet...
30-06 perhaps??? I think it because is the perfect bullet and weight for the old and trusty THIRTYSIX...
I hope I don´t miss the shot! jhahahaha
 
There MUST be, .....
Excellent round for THE KING OF THE CALIBERS
I love the 30-06!
 
Like others have posted, either of the bullets in the OP will work fine. I have used Accubond, TSX, and TTSX bullets on different PG hunts, and all of them performed very well. I even used 140 grain Ballistic Tip bullets in a 7mm RM on my first PG hunt and made one shot kills on Kudu, Blue Wildebeest, and Gemsbok.

I would advise AGAINST taking two different bullets and/or weights in the same cartridge for a PG hunt, as they probably will not have the same trajectories and you don't want to be re-sighting in your rifle during the hunt. You never know if your shot opportunity will be at 30 yds or over 300 yds.

I've taken at least 35 big game animals with TSX and/or TTSX bullets at ranges from 30 yds to 348 yds, and have not had any 2" entrance holes or pencil pass throughs.
 
Why is everyone forgetting the Nosler Partition?
 
Why is everyone forgetting the Nosler Partition?

Because it's supremely over priced and the technology is obsolete. There are a lot better choices.
 
A tipped TSX 168g in 30-06 will take care of everything from the smallest to largest plains game. Perhaps a bit small for giraffe. I've used it with no problems up to eland; my wife has taken springbok.

Don't worry about the tipped version opening too soon: they penetrate fine. If the tipped opens quicker than the standard, that will be a plus on the very small animals. It won't matter on the big ones.
 
Why is everyone forgetting the Nosler Partition?

Hello Archer36,

Personally, when hunting in conditions that will not present long shots (beyond about 300 yds) I prefer JSP in Round Nose or Flat Nose profile, at moderate velocity, in heavy weights for whatever caliber I am using (for example; 220 gr in .30 caliber and 300 gr in .375 caliber).
But for conditions where 400 or more yd shots are not rare and yet a 50 yd shot could also be possible on the same day, I have had very good luck with Nosler Partitions.

I like the fact that the nose is very soft, thereby expanding easily, even at very long range, (attendant lower velocity).
Plus, at close range, the front tends to smear off, leaving a cylindrical shaped "drill bit" that penetrates very well, due to the jagged part left from the front shattering or smearing away.

Besides using them here in Alaska, in various calibers, I also used them on my very first safari (Namibia) for PG where the shots can be quite long.
My rifle was a Model 98 Mauser in .300 H&H, with 4x Zeiss and I shot 180 grain Nosler Partitions at a bit over 2800 fps (most accurate load in my particular rifle).
It proved extremely effective not just at close range, but out to a bit past 400 yds and various yardages in between.

That being said, I also very much like the Swift A-Frame bullets.
One could say they are something like a strengthened version of the Nosler Partition.
My hunting partner during that Namibia trip used 140 gr A-Frames in his 22" barreled .270 (also a '98 Mauser) and I was amazed.
That was my first exposure to A-Frames in action but not my last and I have been very sold on them to this day.

Well anyway, back to the N. Partition, I like that bullet within it's velocity limitations (another character I hunt with shattered a 260 grainer against a moose brisket at very close range, fired from his .375 Weatherby and no part of the resulting shrapnel made it into the vitals).

The .308 Winchester with 180 gr Nosler Partition will have no such over-velocity problem and it seems like it'd work well for what you plan to do.
But if eland is on your list, and you still plan to use your .308 for it, I would go with the A-Frame instead.

I do not trust any hollow point bullet for my hunting needs however, many people here and elsewhere have had excellent results with them (and I know of some who have not).
Anyway, as many here have suggested, you might consider going with the TSX or TTSX but in a light enough bullet to get plenty velocity (150 gr?).
The higher velocity is to help insure you don't experience any failures to expand (they're harder than lead).

There is no perfect bullet for all calibers, at all velocities, to hunt all species, in all conditions.

Cheers,
Velo Dog.
 
Last edited:

Forum statistics

Threads
57,571
Messages
1,234,382
Members
101,373
Latest member
TammyLoy35
 

 

 

Latest profile posts

dlmac wrote on Buckums's profile.
ok, will do.
Grz63 wrote on Doug Hamilton's profile.
Hello Doug,
I am Philippe from France and plan to go hunting Caprivi in 2026, Oct.
I have read on AH you had some time in Vic Falls after hunting. May I ask you with whom you have planned / organized the Chobe NP tour and the different visits. (with my GF we will have 4 days and 3 nights there)
Thank in advance, I will appreciate your response.
Merci
Philippe
Grz63 wrote on Moe324's profile.
Hello Moe324
I am Philippe from France and plan to go hunting Caprivi in 2026, Oct.
I have read on AH you had some time in Vic Falls after hunting. May I ask you with whom you have planned / organized the Chobe NP tour and the different visits. (with my GF we will have 4 days and 3 nights there)
Thank in advance, I will appreciate your response.
Merci
Philippe
rafter3 wrote on Manny R's profile.
Hey there could I have that jewelers email you mentioned in the thread?
 
Top